Trapezoidal threads

This is the Biscotti Version of the Convoy S2+ with 6x 7135 chips.

The light has a copper DTP board, anodized tail threads, a smooth reflector, and an AR coated glass lens. It takes an 18650 battery. 

Biscotti is a firmware created by Toykeeper.

 

This is the Convoy C8+, a throw optimized single cell light.

It has a smooth reflector and your choice of emitter. 

It has an AR coated glass lens and a copper DTP board. This version of the light runs the Biscotti firmware (created by ToyKeeper). It takes an 18650 battery.

Specs:
Color temperature: 4000-4500K
Mode: 1%-10%-40%-100% (double-click the side to press the switch---->burst), the maximum output is 4A
Switch: tail forward switch to control on or off, side switch control mode
Reflector: glossy cup aluminum alloy, maximum diameter 67.8mm, height 48.2mm
LED: GT-FC40 20mm DTP copper plate, maximum luminous flux 3000-3500LM
Maximum range: ANSI 734 meters
Maximum intensity: 135KCD
Waterproof rating: IPX6
Battery: L6 uses two 26650 batteries to supply power, please note that batteries and chargers are not included
Head diameter: 75mm
Outer diameter of battery tube: 35mm
Inner diameter of battery tube: 27mm
Flashlight length: 255mm
Weight: 550g

This is the Convoy L21A, a throw optimized single 21700 cell flashlight. 

It has an SST40 LED and a 6A 12 group Convoy driver. It has a beam distance of up to 750 meters and a brightness of up to 2300 lumens. It also comes in a nice padded box. 

Square threads

This is the Convoy S2+ flashlight with the updated v2 Convoy driver.

This driver has two variants. One is similar to the old kBiscotti driver in that it can be configured to your needs, but it also has thermal regulation and no visible PWM.

The second option is a non-configurable 4 mode driver with mode memory. The modes for this driver are as follows:
0.1%-3%-30%-100%  max current output is 6000mA

The brightness of both drivers is approximately 1800 lumens at 100%. 

The light has a copper DTP board, anodized tail threads, a smooth reflector, and an AR coated glass lens. It takes an 18650 battery. 

Gray has square threads, silver and orange has trapezoidal threads.

A short body tube for Convoy S2+ flashlights which will allow the use of 18350 batteries.

Important: It has been brought to my attention that these tubes are not exactly the same internal diameter at the original 18650 tube. This means some (if not all) protected 18350s, or anything with a thick wrapper may not fit. Unfortunately there is nothing I can do about this, that's just how Convoy makes them.

Not all colors will thread together. Convoy is currently transitioning to a new thread type, so some lights have the old style and some have the new style. If you need to lego them together, please send me an email to make sure color x will be compatible with color y. This issue will be remedied when the thread transition is complete.

 

A host for the S2+ platform. It includes:

1*OP or SMO reflector (see pictures for reference),1*pill,1*head O ring,1*glass,1*spring,1*lanyard

Some colors come with a gift box and clip.

Switch and color reference:

The following size of LED and driver (not included) fit this host:
LED plate:Diameter 16mm
Driver:Diameter 17mm

A host for the S21A platform. 

 

Material: aluminum alloy and brass

Length / Diameter (host) : 122.5mm / 25.9mm

Diameter / Thickness (lens) : 22.8mm / 1.5mm

Diameter / Height (reflector) : 22.8mm / 11.7mm
Bottom hole diameter (reflector) : 7mm

Switch type : 1288switch

Applicable battery type : 21700 lithium battery

weight:75g

 

Notice: LED and driver are not included, you should use LED with 20mm PCB board and driver with 20mm diameter,height of the component on the driver should not exceed 6mm. We also sell adapters for 17mm components.

Some rewrapped cells may be too thick to fit properly in the light. 

20*12mm orange peel reflector for Convoy S2+ flashlights. 

This UV filter will fit the Convoy S2+

Flashlight and filter sold separately.

A holster for the Convoy S2 and S2+

Anti-reflective coated glass lens for Convoy S2/S2+/S3/S6/S9 BD03 flashlights.

10.5x1.6mm.

For Convoy flashlights. 5000mA current output. 17mm.

A 7135 based driver running Biscotti suitable for the Convoy S2+.

This driver isn't compatible with the lighted switch out of the box.

Diameter: 17mm

7135*3 output current 1050mA (MAX)
7135*4 output current 1400mA (MAX)
7135*6 output current 2100mA (MAX)
7135*8 output current 2800mA(MAX)

A switch for many Convoy flashlights. This is the standard non-illuminated version. There is an illuminated version which we also sell.

Price is per switch.

Like the smaller Convoy holster, but with enough room to accomidate a larger head.